Mobile home heating repair done right the first time
Furnace Repair for Mobile Homes in Loveland
Furnace Repair for Mobile Homes in Loveland is what we do every day, from Downtown Loveland to Campion. Manufactured homes use different cabinets, different venting, and different clearances than site-built houses, and we know those systems inside out. When your heat quits on a cold Colorado night, we diagnose it fast and fix it right.
Live phone supportUpfront optionsBacked workmanship
What's included
What Our Mobile Home Furnace Repair Includes
Every mobile home furnace repair visit covers the full diagnostic and the repair itself, plus the safety checks that keep your family protected. Here is what is built into the price, and what we handle as a separate quote if it comes up.
Full System Diagnostic
We test gas pressure with a manometer, voltage and continuity with a multimeter, and combustion with an analyzer. The diagnostic covers the igniter, thermocouple, gas valve, blower motor, limit switches, and control board so we find the real cause, not just the symptom.
Heat Exchanger Inspection
We run an inspection camera through the heat exchanger on every visit. Cracks and soot are the leading safety risk in older manufactured home furnaces, and catching them early prevents carbon monoxide problems. If we find damage, you see the footage and get honest options.
Venting and Flue Check
Flue pipes on mobile homes corrode and separate over time. We inspect the full vent run, check clearances against manufacturer specs, and reseal or replace any section that is leaking or out of spec. Proper venting is not optional on a sealed combustion furnace.
Duct and Airflow Verification
We check the crossover duct, register airflow, and temperature rise against ACCA standards. Poor airflow is behind most short cycling and uneven heating complaints in manufactured homes, and it is usually a cheap fix once it is identified.
Filter Replacement
We swap in a fresh furnace filter sized correctly for your cabinet and show you how to change it going forward. A clean filter protects the blower motor and keeps the heat exchanger from overheating, which is the simplest maintenance you can do.
Post-Repair Test Cycle
After the repair, we run the furnace through a complete heat cycle and verify temperature rise at the registers. Nothing gets signed off until the system proves it works. You get a written summary of what failed, what we replaced, and the warranty terms.
Service overview
Furnace Repair for Mobile Homes in Loveland
Furnace Repair for Mobile Homes in Loveland means working on the specific furnaces built for manufactured housing: downflow and upflow units in tight closets, sealed combustion chambers, and venting that has to meet HUD and manufacturer clearances. We pull the access panel, test the igniter, check the gas valve, and read the heat exchanger for cracks. Most mobile home furnaces are Goodman, Rheem, or Carrier units, and each one fails in its own predictable way.
Loveland sits in Larimer County, where winter nights drop below 10 degrees and the wind off Boyd Lake cuts straight through skirting. That cold exposes weak blower motors and cracked flue pipes fast. If you are searching for mobile home furnace repair near me Loveland, we run same-day calls across 80537, 80538, and 80539. We also handle manufactured home furnace repair cost Loveland Colorado questions up front, so you know the number before we start.
How we workWe verify the cause, compare realistic options, and confirm the repair before we leave.
The service timeline
What to Expect on Service Day
The process flexes to the condition, but these checkpoints keep decisions clear.
Call and Triage
You call 970 489 0849 and describe what the furnace is doing: blowing cold air, short cycling, banging, or dead silent. We ask a few quick questions, give you a two-hour arrival window, and put the right parts for your brand on the truck. Most calls get scheduled the same day.
Full Diagnostic
The technician pulls the panel and runs a manometer on gas pressure, a multimeter on the control board and limit switches, and a combustion analyzer on the flue. Fifteen to thirty minutes gets us a real answer instead of a guess. You get the findings in plain language.
Price Before Work
We hand you the diagnosis and a flat price for the repair. If it is a $220 igniter, you hear $220. If the heat exchanger is cracked and a replacement makes more sense, we say so and quote both paths. You decide, and nothing starts until you say go.
Repair and Test
Most repairs take one to three hours. We replace the failed part, reseal the cabinet, and check the flue pipe and duct sealant while we are in there. Then we run the furnace through a full heat cycle and verify temperature rise at the registers before we call it done.
Walkthrough and Warranty
Before we leave, we show you what failed, what we replaced, and how to keep it running. You get a written workmanship warranty and a filter reminder for the next change. If anything acts up inside the warranty window, you call us and we come back.
Tools & methods
Tools and Methods We Use
Purpose-built equipment, used by trained technicians, so the job is done accurately the first time.
Combustion Analyzer
Measures carbon monoxide, oxygen, and flue temperature to confirm the furnace is burning cleanly and venting safely. This is the tool that catches problems a visual inspection would miss.
Manometer
Reads gas pressure at the valve and draft pressure in the flue. Correct gas pressure is essential for proper ignition and safe combustion in manufactured home furnaces.
Multimeter
Tests voltage, continuity, and resistance across the control board, limit switches, igniter, and blower motor. Most electrical faults are pinned down in minutes with this tool.
Inspection Camera
Slides into the heat exchanger to reveal cracks, soot, and corrosion that cannot be seen from the outside. Every mobile home furnace inspection includes a camera pass.
Vacuum Gauge
Checks static pressure in the ductwork to confirm the blower is moving the right amount of air. Poor static pressure is a hidden cause of short cycling and uneven heat.
Fin Comb and Nut Driver Set
Straightens bent condenser and evaporator fins and opens furnace cabinets without stripping screws. Small tools, but they keep the equipment in better shape and speed up service.
Thermometer
Measures supply and return air temperatures to calculate temperature rise. We compare the reading against the manufacturer's rating plate to confirm the furnace is running in spec.
Use cases
When to Call for Mobile Home Furnace Repair
These examples show how the service framework adapts rather than forcing every call through one repair.
Short Cycling Solved with Airflow Fix
A manufactured home near Boyd Lake was short cycling every four minutes. The gas bill had climbed 35 percent over the previous winter, and two rooms stayed cold no matter what the thermostat was set to. → The crossover duct had torn where the skirting shifted, and the filter was clogged solid. We repaired the duct, resealed it, and replaced the filter. Static pressure dropped back into range, cycling stopped, and the gas bill came down by roughly 25 percent the following month.
Pilot Light Fixed, Replacement Avoided
A homeowner in Downtown Loveland was told by two other companies that the 1990s furnace needed full replacement. The pilot light kept going out, and the quotes were north of $4,000. → We tested the thermocouple and found it was reading out of spec. A $210 replacement solved the problem completely. The heat exchanger passed inspection with the camera, and the furnace has run without issue for two full winters since.
Problems we solve
Mobile Home Furnace Problems We Fix in Loveland
Most manufactured home furnace failures fall into a handful of patterns. Here are the ones we see most often on Loveland service calls, what happens if you ignore them, and how we fix them.
Furnace blowing cold air instead of heat
We test the igniter, flame sensor, and gas valve to find why the burner is not lighting. Most cold-air calls trace back to a failed igniter or a dirty flame sensor, and both are same-day fixes with parts we carry on the truck.
Furnace short cycling on and off every few minutes
We check airflow first, since a clogged filter or crushed crossover duct causes most short cycling in mobile homes. If airflow is fine, we test the limit switch and control board. Fixing the root cause stops the cycle and protects the equipment.
Pilot light will not stay lit
A failing thermocouple or dirty pilot assembly is usually the culprit. We replace the thermocouple with an OEM-spec part, clean the assembly, and test the full ignition sequence. Typical cost runs $180 to $280.
Furnace making banging or rumbling noise
We inspect the burners, gas pressure, and ignition timing with a combustion analyzer. Cleaning or replacing the burners and resetting gas pressure usually solves it. We also check the heat exchanger for damage caused by repeated delayed ignition.
Pricing process
Mobile Home Furnace Repair Pricing
$180 - $1,200 depending on the repair
Part cost and availability
Common parts like igniters, thermocouples, and filters are inexpensive and on the truck. Blower motors, gas valves, and control boards cost more and occasionally need to be ordered for older or unusual models.
Furnace age and brand
Parts for Goodman, Rheem, and Carrier units are widely available. Older or discontinued models can be harder to source, which affects both the part price and the wait time.
Access and cabinet layout
Some mobile home furnace closets are tight, and getting the unit out for a blower motor replacement takes longer. We quote the labor honestly based on what the job actually requires.
Customer reviews
What Loveland Customers Say
★★★★★
“Our 1998 single-wide lost heat on a Friday night in January. They answered the phone, showed up by 9 p.m., and had a new blower motor in by 11. The tech showed me the old motor and explained exactly what failed. House was back to 70 degrees before midnight. That is the kind of service you remember.”
★★★★★
“Furnace was short cycling every few minutes and the gas bill was climbing. They found a clogged filter and a failing limit switch, fixed both for under $300, and the cycling stopped that day. They also checked the heat exchanger with a camera and showed me the footage. No pressure, no upsell, just honest work.”
★★★★★
“Pilot light kept going out and two other companies told me I needed a whole new furnace. Loveland FurnaceRepair replaced the thermocouple for $210 and it has run perfectly for two winters now. They saved me thousands. I have recommended them to three neighbors in the park already.”
How much does Mobile Home Furnace Repair Loveland CO cost?
Most mobile home furnace repairs in Loveland run $180 to $450 in 2026. An igniter or thermocouple swap sits at the low end, while a blower motor or gas valve replacement lands higher. Diagnostic visits are flat-rate and the price is quoted before any work starts, so the number you hear is the number you pay.
Who repairs mobile home furnace near me in Loveland?
We do, and we cover every Loveland neighborhood from Downtown to Campion and out past Devil's Backbone. Call 970 489 0849 and we will schedule a same-day or next-day visit across ZIP codes 80537, 80538, and 80539. Emergency calls get answered 24/7, including weekends.
Is Mobile Home Furnace Repair Loveland CO different from standard repair?
Yes, in three ways. Manufactured home furnaces use tighter cabinet clearances, dedicated downflow or upflow ducting, and venting that must meet HUD and manufacturer specs. A technician who only works on site-built homes will often miss the crossover duct and skirting issues that cause half the problems we see in Loveland mobile homes.
How long does mobile home furnace repair take in Loveland?
A typical repair takes one to three hours once the technician arrives. Simple part swaps like an igniter finish in under an hour. Blower motor or heat exchanger work can run three to five hours. If a specialty part has to be ordered, we tell you the exact timeline before we leave the first visit.
Related services
Related Services
Furnace Replacement
When a mobile home furnace is past saving, we size and install a replacement built for manufactured housing. Manual J load calculation, correct clearances, and full commissioning are included so the new unit heats evenly from end to end.
Furnace Maintenance & Tune-Ups
An annual tune-up catches weak igniters, dirty burners, and airflow problems before they strand you in January. We clean, test, and adjust the whole system, which is the cheapest way to avoid a mid-winter mobile home furnace repair in Loveland.
Emergency Furnace Repair
No heat at 2 a.m. is an emergency in a Colorado winter. We answer the phone around the clock and roll a truck to Loveland mobile homes with the parts needed to get heat back the same night whenever possible.Ready when you are
Get Your Mobile Home Heat Back Today
Furnace Repair for Mobile Homes in Loveland is one call away. We answer 24/7, quote the price before we start, and back every repair with a written workmanship warranty. Call 970 489 0849 and we will get a technician headed your way.
Talk with the local team
Request Furnace Repair for Mobile Homes
Call 970 489 0849 any time, day or night. We answer live for emergency no-heat calls and book standard service Monday through Friday, 8 a.m. to 6 p.m. Most Loveland calls get a same-day window, and we text you when the tech is on the way.